Specifications For the Fitted Club

This  page describes the data gathered by the FitChip and presented in chart form by the FitChip computer analysis program. This data will be used in formulating the final specification of the custom golf clubs that fit  the players SWING TIMING. This timing concentrates on getting the  club/shaft back to straight at ball impact where you achieve your best  performance of distance and accuracy. There is no other fitting system  on the market that addresses this approach with the exception of trial  and error, monitoring performance, which can be limited by time,  prejudice and has no way of truly identifying that the shaft is back to  straight at ball impact and obtaining peak performance. 

Figure 1

image58

Figure 2

image59

The FitChip gathers club head acceleration/club head speed data when placed on any club, which is typically shown in Figure 1. From this data the computer analyzes the data to produce the club head  acceleration curve as shown in Figure 2. This curve is used to locate  the time of peak acceleration or shaft release (point at which the shaft  starts to kick back, time increment 126) and ball impact (time  increment 173). The red line represents the unloading of the shaft, through  1/4  cycle  of   its natural frequency, from the flexed  position back to straight and square at impact. 


In these  charts two different swings are overlaid to demonstrate the players consistency. During the time interval, described by the red line, the  club releases/kicks and must return to straight and square at ball impact for peak performance (best combinations of club head speed and accuracy). Matching this players timing with the club depends on the natural frequency of the golf club shaft as a spring. It is this natural frequency that is derived by the FitChip for each swing.


The frequencies (blue dots) for each swing and the average frequencies  (red dots) for four different clubs are shown in Figure 3. A line drawn  through these points will define the frequencies at which to build each  club in a full set of properly fitted custom golf clubs, as shown in Figure 4.   

image60

                         Figure 3

image61

                          Figure 4

to build each club in a full set of properly fitted custom golf clubs, as shown in the Build-to Table Figure 4. The multiple sloped lines in Figure 3 represent the slope the Golf Industry and most Club Builders build sets too. We build your clubs based upon the slope or curve your Swing Timing requires (the red or yellow line in Figure 3) !


Most standard sets of golf clubs on the market today use identical flex category shafts tipped a consistent 1/2" increment from club to club, and then butt trimmed to the finished length. This process makes each shaft stiffer by approximately 4.3 cycles of natural frequency as the clubs get shorter. Through thousands of fittings with FitChip, we find that very few players are properly fit with this 4.3 cycle progression as predetermined by club and shaft manufacturers. Just as a standard size, off the rack suit, will not fit properly everywhere on the body, seldom does every club in an off the rack set, fit the players swing timing properly, thus most players with these clubs have a favorite club. Most individuals have a unique curve or line depicting their individual swing timing, and their clubs should be built accordingly Figure 5. Sometimes on straight lines, sometimes on curves, sometimes on positive and sometimes on negative slopes. Everyone is different, and unless you have a set of clubs built with this system, you will never have a fully fitted set of clubs, for which you can say, "every club in my bag is my favorite club." 

image62

From Figure 5 you can see the major differences in these players and some unexpected results. For instance the senior player has the stiffest set of clubs from this diverse group of players. This senior player had won the National Senior Amateur and was approached by all the club companies to play their clubs and of course since he was a senior and had a relatively low club head speed they put him in senior shafts. At that time he lost his game completely and came to me to analyze the problem. A FitChip fitting told us he needed the stiffer clubs and almost on a flat line. Once I built this set for him he returned to the winners circle on the senior amateur circuit.


The Club Pro had the long smooth swing with the very early release requiring the slower kick of a soft shaft, However in the shorter clubs They required a stiffer shaft because, on purpose, he was trying for more back spin in the shorter scoring clubs. While in the case of the PGA Pro, a winner of the PGA Championship, his longer clubs fell on the 4.3 slope but the swing timing changed in his shorter scoring clubs to a flat line to achieve more accuracy and consistency.


Maintain the swing that matches your clubs with SYNCA SWING, our Swing Trainer


Questions: 
​TEL:         239 910 7815 
E-Mail:     fitchip@hotmail.com 

Contact Us to Find Your Specifications

Better yet, see us in person!

We like meeting our customers, so feel free to make an appointment during normal business hours.   

Perfected Golf Group, Ltd, Custom Clubs

502 Schrock Rd., columbus, OH 43229, US

(239) 910-7815

Hours

Drop us a line!

Cancel